Miele F11 Error: What It Means and What You Can Safely Check
Seeing an F11 error flashing on your Miele washing machine or dishwasher is one of the most common headaches for Miele owners. The machine usually beeps, stops mid-cycle, and leaves a pool of soapy water sitting at the bottom.
The good news is that an F11 error doesn’t always require a major repair. Often, a coin, a lemon pip, or a blocked sink spigot is all that is stopping the water from getting out. Here is what the F11 code actually means, what you can safely check yourself, and when it is time to call in a technician.
What Does the Miele F11 Error Mean?
On both Miele washing machines and Miele dishwashers, F11 means the water isn’t draining away.
Your machine gives the drain pump a set amount of time to empty the water out of the drum or wash tub. If the water level sensor detects that water is still inside when that timer runs out, the machine stops the cycle and displays F11 (or a drainage warning) to stop it from overflowing.
Seen a different code? Look up what your fault code means, in plain English.
Safety First Before You Check Anything
Water and electricity do not mix. Before you touch any filters, hoses, or water inside your appliance:
- Switch the appliance off at the wall power point and unplug it if you can reach the plug safely. Do not just press the power button on the front of the machine.
- Stay clear of water near power. If the power point or floor is wet, don’t touch it: switch off at the switchboard or call us.
- Never open the machine’s panels or attempt any electrical or internal mechanical work yourself. Stick strictly to the user-accessible filters and external hoses designed for homeowner cleaning.
- Let the water cool down. If the machine stopped in the middle of a hot wash, wait an hour before opening filters so you don’t burn your hands.
- Watch out for sharps. In dishwashers especially, broken wine glasses often hide in the drain sump. Wear thick rubber or gardening gloves before reaching inside.
Safe Checks for a Miele Dishwasher Showing F11
Once the dishwasher is switched off at the wall, work through these simple checks:
1. Clean the filters in the base of the tub
Open the dishwasher door and scoop out any standing water with a plastic cup or sponge. Turn the handle on the flat mesh filter at the bottom of the tub to unlock it, and lift the filter assembly out. Rinse it thoroughly under the kitchen tap with warm soapy water and a soft brush to clear away grease and food scraps.
2. Check the non-return valve and pump impeller
Directly underneath where the filter sits, you will see a small clip-on cover (the non-return valve) with a vertical loop handle. Unclip it and lift it out. Beneath that cover sits the small spoked wheel (impeller) of the drain pump. Wearing gloves, feel gently around the impeller for broken glass, olive pits, toothpicks, or seeds. Gently turn the pump blade by hand to check it spins freely (power off). Clip the cover firmly back into place. The dishwasher will not drain properly if this cover is left off or loose.
3. Check the drain hose under your kitchen sink
Look inside the cupboard under your kitchen sink where the dishwasher drain hose attaches to the sink trap (spigot). Make sure buckets or cleaning bottles haven’t pushed against the hose and kinked it. If you have just had new sink plumbing installed, a blocked sink spigot, or one whose plastic knock-out was never removed, will also trigger an immediate F11 error.
Safe Checks for a Miele Washing Machine Showing F11
Once your washing machine is switched off at the wall, grab a few old towels and a shallow baking tray or bowl:
1. Empty and clean the front drain filter
Open the small flap at the bottom front corner of your washing machine (how it opens varies by model).
Slide a shallow tray underneath the flap. Slowly unscrew the round drain filter cap half a turn. Do not pull it straight out all at once, or all the water in the drum will gush onto your floor. Let the water trickle into your tray, screw the cap closed whenever the tray fills up, and repeat until the drum is empty.
Once the water stops flowing, unscrew the filter completely and pull it out. Remove any coins, hairpins, lint, or collar stays, and check that the little pump blade right at the back of the housing isn’t jammed by a baby sock. Clean the rubber seal on the cap and screw it tightly back in.
2. Check the drain hose and laundry tub connection
Look behind the machine to make sure the grey corrugated drain hose hasn’t been squashed or bent sharply against the wall. If the hose drains into a spigot under your laundry tub, unscrew the hose cuff over a bucket and check whether lint and soap scum have blocked the plastic nozzle on the trap.
When to Call Livelee Electrical
If you have cleaned the filters, checked the pump impeller, and made sure the external hose is clear, and the F11 error comes right back, the fault is internal. Common internal causes include:
- A burned-out or failing drain pump motor that works when cold but seizes up once warm.
- A blocked internal sump hose or air pressure chamber (which stops the machine from realising the water has actually drained).
- A faulty water level pressure sensor or wiring fault.
We repair Miele washing machines and dishwashers in homes right across Sydney. Miele vacuums are the exception: you drop them off and collect them at our Rose Bay workshop, by arrangement. Our call-out is $199, and you can view all other pricing info on our pricing page.
We cover Rose Bay outwards: the Eastern Suburbs, the CBD and inner city, the Inner West out to Haberfield, the Lower North Shore and south through Botany to La Perouse. See every suburb we cover, with its postcode.
Frequently Asked Questions
Can I keep resetting the F11 error and running the machine?
If you cleared a coin or seed out of the filter, run a short drain or rinse program to test it. If the filter was already clean and the machine still won’t drain, don’t keep restarting it. Running a jammed or failing pump repeatedly can overheat the pump or damage the control board.
Why does my Miele dishwasher make a rattling noise before showing F11?
A rattling or grinding sound during the drain phase usually means a small piece of hard debris (like a piece of broken crockery, a fruit pip, or glass) is flicking against the drain pump blades. Switch off at the wall and check under the non-return valve cover using gloves.
How much does it cost for you to come and fix an F11 error?
Our call-out is $199 across Sydney. For all other prices, please check our pricing page.
How fast can I book a technician?
You can book online. You simply select up to three days and a time window, and we will confirm one of them by SMS. You can also call us Monday to Friday, 8:30am to 5:30pm.
Do you have good reviews from other Sydney homeowners?
Yes. We have a 4.8 rating from 38 Google reviews for our appliance repair work across Sydney.
Still stuck with a Miele F11 error?
Don’t wrestle with bowls of soapy water. Book a home repair visit online or call Livelee Electrical on 0434 000 303 (Monday to Friday, 8:30am to 5:30pm).